vSphere / Lab For Beginners: Part 2 – Installing & Configuring Virtual Center

Where Are We and What’s Next?

At this point in our lab build we have our ESXi hosts up and connected to some storage but nothing else.  We need a tool to manage all our hosts and provide accss to all the cool features that VMware and Virtualisation is known for such as moving VMs between hosts, advanced networking, HA, load balancing etc.

Within vSphere this is Virtual Center.  Currently available in two formats.  One being an installable that can run on a Windows Server and one being a deployable appliance that is simply pushed out to a host without any other OS requirements.  For this guide we are going to be deploying the appliance version (known as the Virtual Center Server Appliance, VCSA).  This is because it’s now the recomended version to use from VMware and the Windows version is probably going to be phased out sometime in the near future.  The VCSA also doesnt require a Windows licence and the patching that goes with it either.  and finally, for a lab environment, the requirements are a little lower so it’s a better fit.

Virtual Center Server Appliance: It’s More Than One Thing!

One thing to note before we proceed is that the VCSA is actually MORE than one component. but, for the purposes of simplicity I’m refering to the suite as one entity in this beginners guide.  If your curious the VCSA is actually split in two.  The vCenter Management Server (responsible for managing the environment and the ‘thing’ you actually log on to) and the Platform Services Controller [PSC] (which deals with mutiple things like sign on, certificates, licensing etc.)  The PSC can be installed with the VCSA or split out to a seperate box for high load installs.  In this lab we’re going to use the embedded PSC.

Before You Start: Sort Out DNS

vSphere in general relies heavily on name resolution to work correctly. Indeed, installing the Virtual Center Server Appliance without having DNS in place first (i.e. using the IP address) can cause issues further down the line such as the inability to change the hostname without the system falling over or other such quirks.

So, before going any further we are going to create a DNS server on your first ESXi host.  In my case I have installed a Windows 2012 R2 Active Directory VM on our first ESXi host and configure a domain and DNS.  I’m not going to cover how to configure Active Directory in this post but before going any further you should ensure that a domain for you lab exists (in this example ‘lab.local’) as well as  forward and reverse DNS lookup zones with entries for your ESXi servers and Virtual Center Server Appliance.  In my case:

Reverse Lookup Zone: Three static entries for ESXi and VCSA and the autocreated entry for the AD server.

Screen Shot 2016-07-26 at 22.08.46

Forward Lookup Zone Entries: For the two ESXi servers and the Domain controller.

Screen Shot 2016-07-26 at 22.08.31

and  the entry for the VCSA about to be deployed.

Screen Shot 2016-07-27 at 22.09.07

If you are starting from scratch and need to create a new VM to install a Windows server / Active Directory to you can follow the steps below.  Otherwise skip to the ‘Deploying the VCSA’ step.

Creating A New VM From Within ESXi

Log on to your first ESXi host via the https://<esxiHost>/ui URL as root and select the Virtual Machines entry on the left.  Now Select Create / Register VM on the right.

Screen Shot 2016-07-27 at 22.11.57

This opens a New Virtual Machine Wizard.  Selct Create New Virtual Machine.  Click Next.

Screen Shot 2016-07-27 at 22.12.11

Enter a name for your VM and select the Compatibility, Guest OS Family and Guest OS Version.  For Compatibility it is best to select the version that matches you ESXi version.  It is also important to select the right Guest OS family (Windows, Linux etc.) and version as this determines the makeup of key elements of the the virtual hardware of the VM (disk controllers etc).  Selecting incorrect family and /or versions can cause performance issues or, at it’s worst, a failure of the VM to turn on.  Once specified, click Next.

Screen Shot 2016-07-27 at 22.12.49

Select your datastore where you would like to store the VM and click Next.

Screen Shot 2016-07-27 at 22.13.19

Here you can configure  the VMs resources tot he size you require. CPU, Memory and Disk can all be set here.   For compatibility reasons I would recomend leaving everything as default except for disk space and RAM.  It should be noted that with most VMs, unless they are performing an explicitly parallel workload the rule is ‘1 x vCPU every time’.  WHY is more advanced but, for now. leave it as a 1 CPU VM and click Next.

Screen Shot 2016-07-27 at 22.13.43

You’ll be given a summery of the options you specified.  Click Finish and the  wizard will close and the VM will be created.

Screen Shot 2016-07-27 at 22.13.56

Notice, back on your main screen, the recent tasks pane at the bottom of the screen will show the progress and, hopefully, success status of the VM creation.  You are now able to start the VM and install an OS to it.

Screen Shot 2016-07-27 at 22.14.13

With all of the above in mind and DNS entries set up for you ESXi and to be installed Virtual Center Server Appliance we can deploy the VCSA into our environment and get going.

Deploying The VCSA (Automated)

In vSphere 6 the VCSA can be deployed the traditional way, clicking through wizards etc.  or using a configfile and a simple command line to automate the whole process.  We’re going to be using the automated method for this guide as I firmly believe that Automation is the way forward and the principals followed here carry forward in to the more advanced areas of vSphere and are worth exploring right away.

NOTE: The following is shown using a Windows PC as the client.  This can also be done via a Mac.  It’s just the kick off command that changes.

What You’ll Need

For this section of the guide you’ll need:

  • A Windows PC on the same network as the ESXi hosts previously set up.
  • Windows Powershell
  • The VCSA ISO file (I used VMware-VCSA-all-6.0.0-3634788.iso from VMware site).
  • The ability to mount .iso images (Native to Windows 10).

Optionally, if you want to follow the command line driven configuration of datacenters and hosts you will need.

  • VMware PowerCLI (installed on your Windows PC)

Step 1: Mount the VCSA ISO and Configure Settings.

Mount your VCSA ISO.  In Windows this is done by Right-Clicking the VCSA .iso file and selecting Mount.

Navigate to <CD Drive>:\vcsa-cli-installer\templates\install and copy the embedded_vCSA_on_ESXi.json file to somewhere simple to access (such as c:\temp)

Open the .json file and edit in the values as you require for your environment.  I’ll explain the requirements for the values after this example (shown).

NOTE: The files here are slightly different between vSphere 6.0 and 6.5.  Both are shown below.

JSON Config For vCenter 6.0

    "__version": "1.1",
    "__comments": "Sample template to deploy a vCenter Server with an embedded Platform Services Controller to an ESXi host.",
    "target.vcsa": {
        "appliance": {
            "deployment.network": "VM Network",
            "deployment.option": "small",
            "name": "VCSA6",
            "thin.disk.mode": true
        "esx": {
            "hostname": "",
            "username": "root",
            "password": "aRandomPassword",
            "datastore": "Datastore1"
        "network": {
            "hostname": "",
            "dns.servers": [
            "gateway": "",
            "ip": "",
            "ip.family": "ipv4",
            "mode": "static",
            "prefix": "24"
        "os": {
            "password": "anotherPassword",
            "ssh.enable": true
        "sso": {
            "password": "evenMorePasswords",
            "domain-name": "vsphere.local",
            "site-name": "Home-Lab-SSO"

So, what are the values that need filling in?  From the top:

appliance:deployment.network - This is the name of the network created in part 1 of the guide.  If you didn't change anything it's 'VM Network'.

appliance:deployment.option - This dictates the amount of CPU, DISK and RAM allocated to the VCSA based on VMware's t-Shirt sizes.  Small is good for up to 100 hosts and 1000 VMs and is perfect for a lab.  There is a Tiny option but you can hit the VM limit in a lab quite quickly.

appliance:name - The text name that you wan to call the VCSA.

appliance:thin.disk.mode - Either true or false.  vSPhere can, simplistically, allocate all disk space requested to a VM at creation or as it is used (more efficient).  I recomend true in this instance.
esx:hostname - This field is populated with the IP address / hostname of the ESXi server you want to deploy this VCSA to.  NOTE: Use IP if DNS is not set up corretly at this stage but preferably use DNS as this can stop known issues arising later if you want to rename the appliance or do anything that relies on FQDN.

esx:username - The username you want to use to connect to the specified ESXi host.  Usually root.

esx:password - The password for the account specified in the field above. Note this is stored in plain text.

esx:datastore - Then EXACT name of the datastore on the ESXi host to deploy the VCSA on. NOTE: This is case and space sensitive.
network:hostname - This is the hostname this VCSA server. NOTE: vSphere is very, very picky about DNS.  In this example I assume you have deployed a domain controller or have DNS set up WITH an entry for this VCSA server alreaddy created. e.g. labvcas.lab.local pointing to the IP address you want to give this appliance.  If DNS resolution is not ready yet an IP address MUST be used here otherwise the install will fail.  However, this will trigger known issues if you ever want to rename your apliance or change its identity. It is HIGHLY recomended to get DNS sorted at this stage.

network:DNS.servers - This setting requires a list (can be one) of DNS servers for name resolution.  I have set these to be my default gateway (for internet name resolution) and then the IP address of the AD server i intend to build in the lab.

network:gateway - This is the default gateway to the internet in IP format.

network:ip - This is the IP address of this VCSA server you're going to be deploying. 

network:ip.family - specifies wether the above address is in IPv4 or IPv6 format.  Default is IPv4.

network:mode - Choose between static or DHCP.  Static is prefered for predictability.

network:prefix - This field is the subnet mask of the network for the VCSA in slash notation. (i.e. 24 =

os:password - This specifies the root password for the VCSA and is needed for access to the console or SSH access. NOTE: stored in plain text.
os:ssh.enable - A true or false value specifying wether you want to enable SSH access to the VCSA.  AS this is a lab I have enabled it in the example.
sso:password - This sets the default password for the administrator SSO (the in built authentication system) account.

sso:domain-name - The domain name for the SSO component install. NOTE: This cannot be the same as an existing orsoon to be existing Windows domain.  I have used vsphere.local (so the admin account is administrator@vsphere.local). 

sso:sso-name - The name of the SSO site.  NOTE: Spaces not allowed.

Once all of the values have been filled in for your envionment you are ready to deploy the VCSA and automatically configure it with the settings in the JSON  file.

JSON Config for vCenter 6.5/6.7

Note that the value you will need to fill in stay the same but the filehas additional sections at the end that are required for the install to sucessfully complete.

 "__version": "2.3.0",
 "__comments": "Sample template to deploy a vCenter Server Appliance with an embedded Platform Services Controller on an ESXi host.",
 "new.vcsa": {
 "esxi": {
 "hostname": "esxi01.lab.local",
 "username": "root",
 "password": "Password1!",
 "deployment.network": "VM Network",
 "datastore": "Datastore1"
 "appliance": {
 "thin.disk.mode": true,
 "deployment.option": "small",
 "name": "LABVCSA"
 "network": {
 "ip.family": "ipv4",
 "mode": "static",
 "ip": "",
 "dns.servers": [
 "prefix": "23",
 "gateway": "",
 "system.name": "labvcsa.lab.local"
 "os": {
 "password": "Password1!",
 "ssh.enable": true
 "sso": {
 "password": "Password1!",
 "domain-name": "vsphere.local",
 "site-name": "HomeLabSSO"
 "ceip": {
 "description": {
 "__comments": [
 "++++VMware Customer Experience Improvement Program (CEIP)++++",
 "VMware's Customer Experience Improvement Program (CEIP) ",
 "provides VMware with information that enables VMware to ",
 "improve its products and services, to fix problems, ",
 "and to advise you on how best to deploy and use our ",
 "products. As part of CEIP, VMware collects technical ",
 "information about your organization's use of VMware ",
 "products and services on a regular basis in association ",
 "with your organization's VMware license key(s). This ",
 "information does not personally identify any individual. ",
 "Additional information regarding the data collected ",
 "through CEIP and the purposes for which it is used by ",
 "VMware is set forth in the Trust & Assurance Center at ",
 "http://www.vmware.com/trustvmware/ceip.html . If you ",
 "prefer not to participate in VMware's CEIP for this ",
 "product, you should disable CEIP by setting ",
 "'ceip.enabled': false. You may join or leave VMware's ",
 "CEIP for this product at any time. Please confirm your ",
 "acknowledgement by passing in the parameter ",
 "--acknowledge-ceip in the command line.",
 "settings": {
 "ceip.enabled": true

Step 2: Deploy the VCSA

Open a PowerShell window and run the vcsa-deploy.exe from the  VCSA ISO with the path to the JSON file appended to the end (as shown).

Please NOTE: Where you run this from needs to be able to resolve the FQDN of the domain controller, ESXi server etc.  So, in my case I ran this on my laptop and had to add the FQDN information of my lab servers to my HOSTS file (C:\Windows\System32\drivers\etc\HOSTS)

For vCenter 6.0

<DRIVE>:\vcsa-cli-installer\win32\vcsa-deploy.exe c:\temp\<json-file> --accept-eula

For vCenter 6.5

<Drive>:\vcsa-cli-installer\win32\vcsa-deploy.exe install C:\temp\<json-file> --accept-eula --acknowledge-ceip


There will be a prompt asking you to accept the SSL certificate of the ESXi host you’re deploying to.  Type yes and press Enter.

Accept the fingerprint

The isntaller will now deploy the VCSA image, boot the VM and configure based on your settings.  NOTE: Depending on your storage this can take a VERY long time to deploy and an equally long time to configure and boot for the first time (up to 30 mins).

Example output (note the DNS error near the top NOT killing the process)

Once the deployment is complete you should be able to open a browser window to the VCSA and log in using the administrator@vsphere.local account.

The Two URLs below are for the different access methods.  The first of for the FLASH client, the second for the HTML5 client (6.5 on).


Ignore the security certificate warning and add it to your exceptions list.


Enter your logon credentials as specified in the JSON file earlier. Press Logon.


You have now deployed and logged on to the VCSA.  The main screen (below, known as the vsphere Web Client) should now be visible.  Next up we need to add the ESXi hosts to the VCSA so it can manage and configure them.


Step 3: Create a Datacenter, Cluster and Add ESXi Hosts to VCSA

Going forward I will be showing the processes to set up the basics of vCenter via the GUI as, at this point, it gives a better understanding on how things fit together.  You sgould know that all these steps are possible via the command line (PowerCLI) which is quicker but requires you to know what you want to do.

Now that you are in the VCSA webclient we can start to configure it to manage our environment.  All vSphere administration and configuration is done via the VCSA.  Indeed, once a host is added to the VCSA it will warn you that nothing should be changed if you log on locally to a host.

First order of bnusiness is to create a new Datacenter.  This is a top level logical container for clusters of ESXi hosts.

Right click on the VCSA in the left hand pane and select New Datacenter from the contexrt menu.


Enter a friendly name for this Datacenter and Press Ok.


You’ll now see that the created Datacenter object appears in the left hand pane of the vSphere web client. Again, right-click and select  New Cluster from the context menu.


This brings up a nicly detailed set of options that can be turned on for a cluster.  Give the cluster a sensible name and make sure you turn on DRS and HA.  EVC is optional but nice.

DRS (Dynamic Resource Scheduling) is VMware’s technology for load balancing VMs across all the hosts in the cluster. It can mopve VMs between hosts to allow better usage of available resources.  It’s an awesome feature and should definitly be turned on.  You can leave the defaults for it’s actual configuration and feel safe it wont break anything.

HA (High Availability) monitors VMs to see if they are responsive.  If a host goes down (for example) and HA is turned on the VMs on the downed host will be powered up on the remaining hosts in a crash consistent state.  Not essential for a LAB environment but worth playing with none the less.

EVC (Enhanced vMotion Compatibility) is a nice little feature that allows the movement of VMs across hosts that have CPUs from different generations with different capabilities.  It does this by limiting the CPU feature set used to the lowest common denominator in teh cluster.  Especially handy in Labs if you’re building them up over a period of months an years and might have different hardware.


After Pressing OK you should now have the Datacenter and Cluster Object visible in Virtual Center.


Now we need to add a host to the cluster.  Right click on the Cluster and select Add Host.  This will bring up a wizard to add in a host.  Type the IP (if no DNS is set up) or the Hostname (if DNS is set up) of the first host you want to add and select Next.

NOTE: As always I reomend using the hostname to add your host in as vSphere is sensitive to DNS working correctly for advance functions and adding by hostname implicitly verifies that everything is working correctly10

Type the username (root) and the password for this account and click Next.11

You may get the standard certificate warning when connecting to a host for the first time.  Click Yes.


A Summary page is displayed. Click Next.


You now should assign a licence.  As this is a lab we’re going to use the trial period evaluation mode licence.  Select it and click Next.


You now have to chose wether to enable Lockdown mode.  Lockdown mode, as it says, prevents users from logging directly in to the host. i.e. all access has to be via vCenter.  As this is a lab and we’re going to want to play around, keep this disabled.  Click Next.


Continue now through the wizard to the end accepting the defaults.  This will put any VMs on the host (just vCSA really) in to the clusters default resource pool (this is fine).  When your done, repeat for the other hosts you have installed ESXi on.  You’ll end up with something like this.


Step 4 – Removing those Errors and Warnings

You’ll probably notice that now the cluster is set up there may be some warnings displayed.  Most probably it’s the ones shown below (if you dont have some or all of these, no matter, skip that part).  At this point it’s usually relating to:

SSH Enabled: We deliberatly did this so no worries there.
No CoreDump Target: We need to fix this.
Syslogs on Non persistent storage: We need to fix this also.


Fixing the “Syslogs on non persistent storage” is possible in one step.  Select the first host in the cluster and click:
For vSphere 6.5: Configure > System >Advanced System Settings.
For vSphere 6.0: Manage tab.  Then select the Settings sub-tab and Advanced System Settings from the left hand list.

Scroll down and select the setting labelled Syslog.global.logDir


Right click this setting and select Edit Option


Change the value to match something like that shown below.  I’ve redirected the logs to Datastore1.  NOTE: when editing this value the “[  ]” MUST be kept and the name inside them is case and space sensitive.  It must match EXACTLY the name of the Datastore. Click Save.  Repeat for the other hosts in the cluster.  I like to target each host to a different Datastore.  If you only have the one Datastore target the logs to a seperate folder to avoid confusion.


Now reboot the vCenter appliance and the error relating to the logging should dissappear.

Fixing the CoreDump Error via Command Line

IConfiguring the Coredump location is done via the ESXi command line.  You’ll need to log on to the ESXi Shell via SSH (use PuTTY (Windows) or iTerm (Mac)) and run the following commands to check, look and set the coredump partition.  SSH should be enabled already on your ESXi hosts sa we ensured not to turn it off in setup.

So, if ESXi is complaining that no coredump partition is set you should be able to run the following command and verify this is the case.

esxcli system coredump partition get

This wil show something similar to that shown below (showing that a partition is configured but not active in this case).  NOTE: it may also show a blank entry for both, this is fine.


If the configured partition is not the device you wanted or is blank you can run the following commands to show the available partitions and then set the system to use the desired one.

esxcli system coredump partition list

this will show a list of the available partitions the system can use.  make a note of the “mpx.vmhbaxx.Cx:Tz:Lx” part of the partition you’ll want to use as it is required in the next step.

We can relate this string back to something more physical by checking the storage adapters section on the host in vCenter.  In this case you can see that vmhba33 maps to the USB Storage Controller (i.e. the USB stick ESXi is instalaled on).


If you need to set a new partition as the target (i.e. Configured was blank).  You can now run the command:

esxcli system coredump partition set --partition="mpx.vmhbaxx.Cx.Tz.Ly"
esxcli system coredump partition set -enable true

This will configure the coredump to the partition of your choice.  You’ll need to reboot ESXi to make the change active.

If the correct partition was configured, but not active, simply set it to active by entering the command below and rebooting ESXi:

esxcli system coredump partition set -enable true

After the reboot you can check everything is correct by running:

esxcli system coredump partition get

Now you can see that the active partition is the same as the configured one and everything is ready to carry on.


Fixing the SSH Is Enabled Error

The final warning we see was about the ESXi Secure Shell (SSH) being active.  As mentioned before we probably want this running in a lab but, if you want to know how to remove it, the steps to disable this are shown below.


Simply select the host with the warning in the left pane of the vCenter webclient and then select the Manage tab.   Now select the Security Profile item in the left bar (you’ll need to scroll down), select services area and click edit button.  Select SSH and Stop the service.

Next Steps

Thats the end of the deployment and basic setup of vCenter and ESXI.  You should now have a working ESXi cluster and vCenter and be able to deploy simple VMs all on a single network and get going.  Next up we will cover the configuration of more advanced networking and authentication within vCenter (using a distributed switch over multiple standard switches, joining the lab to a domain) and how to set up vMotion and other cool features of vSphere.


vSphere / Lab For Beginners: Part 1 – Installing ESXI To USB

This post is all about how to install the first part of any vSphere / HomeLab setup.  the basic ESXi client.  It’s intended for beginners who haven’t used vSphere before or those who know a little but are installing on their own for the first time.


This guide assumes that you’re installing on to a physical piece of hardware that will boot from a USB key. Although the process is pretty much the same for SD cards, local storage etc).  It also assumes that you’re installing from an ISO image and no optical drive.

All software used in this guide can be obtained with a free trial licence so you get going  quickly and have a limited playa round.

For advice on choosing hardware suitable for a lab or test environment check out the Open Home Lab project (community run) or ‘Part 0’ of this series for information on the kit this lab weas built on.

Note: This guide was based off vSphere 6.0 however.  This processw is the same for vSphere 6.5 based installs of ESXi.  Differences are called out and noted.

What You’ll Need

For this part of the guide you’ll need:

  • Aa blank USB key (8GB or more, 16GB recomended [for logs])
  • An installed copy of VMware Workstation (Windows) or Fusion (Mac)
  • An ESXi Install.iso image
  • Some shared storage (iSCSI via a NAS shown in guide).
    • any NFS share would also be viable but not shown here.
  • 2 x ‘computers’ to act as hosts for ESXI and run our workloads
    • These will run ESXi from USB.

Trial versions of the software can be downloaded form VMware’s website.

What Are We Going To Do?

The aim here is to install ESXi 6.0 (the beating heart of vSphere) on to a USB stick and then get our hosts to boot  ESXi from that.  We’re then going to set the hosts up so they can communicate and have access to some shared storage.  Then they will be ready to run VMs.

Step 1: Create a Blank VM In Workstation

Open up VMware Workstation and create a new VM  from File > New Virtual Machine.  This bring up a handy Wizard.


Workstation provides an option to attach an ISO to a new VM and boot straight to it when it’s created.  This is perfect for Installing ESXi as, with a few clicks, we’ll have the installer booted and ready to go without any faff!.

Select Installer disc image (.iso): as the option and then browse to the ESXi .iso file you have downloaded from VMware. It’ll probably have an unfriendly name. e.g. VMware-VMvisor-Installer-6.0.0.update02-3620759.x86_64.iso. Click Next.


Now name the VM something friendly (its not being kept so dont worry too much). and, if you can, make the location somewhere fast and local to speed up install times.  Click Next.


This VM isn’t going to do much apart from boot an ISO image (we’re installing to USB remember) so make the disk size 2GB and click Next.


Make sure you tick the Power on this VM after createion option and click Finish.


The VM used to boot the ESXi installer will now be created, turn itself on, and then load the installer program.  Probably less than 30 seconds!.

Step 2: Install ESXi to USB Stick

When you open a console to you’re VM you should probablu see something like this.  Notice there is a countdown timer so, if you’ve been a biy slow, the default option will already have been selected for you…


Once you’ve selected you want to install ESXi you’ll be presented with a chance to back out.  Don’t! Go forth and install (Enter).


Before you go any further you’ll want to ensure that you’ve plugged in your USB key that you with to install ESXi on to and connected it to the VM via VM > Removable Devices > [Your USB Drvice] > Connect.USB Connect

Accept the EULA, you know there’s nothing important contained in it right? (Press F11).


Now you have to start paying attention.  Use the cursor keys to select the USB key from the list If it’s not shown check that you’ve connected the key to the host via the VM menu. Press Enter.


The installer will now scan the disk to see if it’s blank or already has something on it.  Wait a few moments.


In My case I already had ESXi installed on this USB stick so I got the warning shown below (sorry about that).  I chose Install as I wanted to show this as if it were a blank drive going forward.


You should now select a keyboard layout.  Ensure you get this right as it’s a total pain if you set a password down the line and then change the keyboard layout. Press Enter.


Now enter a password for the root account.  This should be secure as it give total access to ESXi. Press Enter.


ESXi will now do some checks to work out what it needs to configure during the install. Just wait a moment.


Now is your final choice to back out.  Check it’s going to install to the correct device (you memorised the HBA number from earlier right?).  Press F11 to begin the install.


The isntall will begin and progress will be shown.  It only takes about 10 mins to a normal (slow) USB stick.


At the end of the process you’ll be greeted with a success screen as shown below. Remove your USB key and turn off the VM in workstation.  You don’t need to press Enter to reboot as we’re done with the VM now.  We just care about the contents of the USB stick.


Step 3: Booting ESXi and Initial Configuration

NOTE: Going forward I’m using a host with no monitor attached.  Instead I have an Intel vPro CPU installed allowing me to use Intem AMT KVM to view the servers boot process.  If you’re intalling to a regular computer ensure you can see the servers output and have a working keyboard to hand before continuing.

NOTE: Most systems are not set to boot from USB by default.  You should chnage the boot priotory in your systems BIOS / UEFI at this point.

Insert the USB key in to your server / computer / host / PC and power it on.  ESXi will load (take about 10 mins) and then will present you with a screen as shown below.


The first thing you must do after installing ESXI is get the basic management network configured.  This is the initial IP  and NIC assignment that ESXi uses to send all traffic between hosts, VMs and your system.  By default it’s set to DHCP and you dont want your IP address changing all the time!

Press F2 to bring up the logon prompt.  Enter root as the username and the password you set in step 2. Press Enter.  If your log on was ucessful nothing wil appear to happen (yes really).  Press F2 again.


The system customisation screen will now be displayed.  This is the area that, in the event of a massive SNAFU in configuration you will always come back to in order to fix things (generally networking).

At this stage we are interested in Configuring the Management Network.  So, select this opeion and press Enter.


This shows the Configure Management Network screen.  We’ll need to configure all of these options but, to start, select Network Adapters. Press Enter.SnapCrab_NoName_2016-6-13_13-30-45_No-00

This is where you can select the NIC that you want to use for the basic management network.  You can select more than one for failover if required but advanced configiuration is far easier from within Virtual Center (covered later).

In this example there are three NICs in my host (onboard lan and an intel Dual port PT adapter [the onces labelled “J6B2….”).  Select the most appropriate one for your system. Press Enter to return to the Configure Management Network screen.


Now select IPv4 Configuration. Press Enter.  This brings up the network settings screen for the NIC assigned to the management network (previous step).  As noted when we booted the host this will be set to DHCP as default.  It is recomended to change this to static and then configure the network settings based on your environment.

The example below shows my setup.  Press Enter. You will rturn to the Configure Management Network screen.


Select IPv6 Configuration and disable IPv6 (restart required).  I’m doing this to simplify things later on and remote and long format IPv6 addresses from troubleshooting steps.  If you want to use IPv6 there is no reason why you can’t leave it on. Press Enter. You will return to the the Configure Management Network screen.


Select DNS Configuration and enter information relevent for your network.  In the example below the primary and secondary DNS entries are my Acrive Directory servers.  It’s crucial that the primary DNS server actually EXISTS at this point.  So, in your environment this may be your internet router.  You should also set the Hostname at this point.  Press Enter.  You will return to the Configure Management Network screen.


Select Custom DNS Suffixes and enter the suffix you are creating for your lab.  This doesn’t have to exist at the moment but if you’re planning on building a domain on the lab enter here what you’re calling the domain.  In my case lab.local. Press Enter.  You will return to the Configure Management Network screen.


Now we have finished configuring the Management Network. Press Escape and the following confirmation should appear.  Press Y to reboot the ESXi host.

NOTE: If you chose to leave IPv6 ENABLED you will simple be asked to Restart the Management Network.  Again, press Y and wait a second.


The host will now restart (a process that takes about 10 mins


Once the host has rebooted you wil have to log in again to be presented witht he main options screen.  We’re going to skip over some of the options here  as they relate to tests or service restarts.  Select Troubleshooting Options. Press Enter.


This display the Troubleshoting Mode Options screen.  Select Enable SSH and Press Enter. this allows us to connect to the ESXi host using PuTTY or similar (iTerm on Mac).  This is handy in a lab as it enables cut-paste of commands.

NOTE: This is only being enabled here as we’re building a lab and it’s useful.  This should obviously not be enabled in a production environment unless there is actuall a problem.

Press Esc to return to the main menu and log out.


This is the basic configuration of ESXi done.  It will now be reachable via https://<IP Address>.  From here you can download the vSphere client for Windows to gain access and install Virtual center.  However, this is useless if you’re on a Mac and the Windows client is going to be replaced soon.  There is a better way….

Step 3: Install the ESX UI Utility

That better way is the ESXi Embedded Host Client.  This is an HTML 5 based management component that isntalls directly on to the host and allows management and configuration of the ESXi hosts from any modern web browser.

NOTE: As of vSphere 6.0U2 this is included as part of the main install and the following step is not technically required.  However, I would always install the latest version and I even came across a bundles version that would not allow me to configure iSCSI until I had upgraded.

Download it here: VMware Embedded Host Client

Essentially, this is a plug-in for ESXi.  These are known as “VIBs” (vSphere Installation Bundle).  Once You’ve downloaded the file and extracted it we need to install it.  The easiest way to do this is to copy the VIB over to the ESXi host using WinSCP.  Place it in simple to get to location (such as /tmp/).

Now, as we enabled SSH in the previous step we can open a PuTTY session to the esxi host and install the  UI utility.

I ran the command esxcli ssoftware vib install -v /tmp/esxui-signed-3843236.vib


Output from that command should look something like the screenshot below.


Once finished you can enter the url https://<IP of ESXi>/ui/ and you’ll get the lovley new html5 interface.  VMware have intimated that this is the way everything is going in the next version of vSphere but, for the moment, this remains an unsupported method of connection.  IMO it works and is FAR better than the old method.


You’ll want to log in at this point.  Use the username root and the password you set up earlier. Click Login.


Welcome to ESXi!


Step 4: Configure Time Synchronisation

ESXi and the rest of the vSphere infrastructure relies heavily on time synchronisation for proper and reliable operation.  Becasue of this it should be configured now before anything else is configured.  This needs to done per installed host.

Click  Manage in the left pane under the host and select the system tab and select Time & Date option.  Select Edit Settings.Screen Shot 2016-07-26 at 22.00.20

Select the Use Network Time Protocol option.  Change the NTP service startup policy and NTP servers to as shown below and click Save.

Screen Shot 2016-07-26 at 22.00.55

Back in the main area select the Actions button and expand NTP service option.  Select start.Screen Shot 2016-07-26 at 22.01.19

NTP will now start and time will be configured on the ESXi server.  Repeat for all installed ESXi server you have.

Step 5: Configure Storage

Once we’re at this point we have a functioning ESXi system with networking but we are still missing one crucial piece of the puzzle. Storage!

Note: vSphere shines and is most useful with shared storage (it’s a requirement for anything vaguley real world) but there is nothing to stop you playing around with one host and locak storage.  You just wont be able to do much.

For the lab to be useful we’ll have to configure some shared storage.  You can use a SAN, NFS shares or iSCSI without issue.  For this lab I’m going to be demonstrating iSCSI running from a Synology NAS (DS1513+).  However, if you dont have iSCSI capability use NFS from whatever share you feel like.  I’ll write an NFS section later.  I’m not going to go over how to set up your storage as that is generally device specific.  We are going to start from within the ESXi Host UI and configure from there.

Example Setup Details

Going forward my example setup consists of 4 iSCSI targets each representing a datastore.  These are called Datastore1, Datastore2, Datastore3 and ISO Store.  These reside on A synology NAS presenting iSCSI over (note the different subnet to the management network).  This is to ensure segregation of storage traffic from data traffic.  It also allows me to monitor my system more easily.

iSCSI Configuration Process

Log on to the ESXi UI via the URL https://<IP Address of ESXi>/ui/ log in as root user with the password you set earlier.  On the left pane, select storage.


In the right hand pane select the Adapters tab and notice that there is only one adapter listed.  This is the USB adapter (if you have a host with a physical HBA this will probably be listed here at this stage, I don’t).  Click the Configure iSCSI item.


This brings up the screen to configure a new Adapter for iSCSI.  For now Enable iSCSI and click the Save Configuration button.


Notice that this now adds another adapter in the list.SnapCrab_NoName_2016-6-13_17-30-43_No-00

iSCSI requires a network connection over a vmkernel port to function correctly and, as mentioned at the start, I am running iSCSI on a seperate subnet.  This requires a little network configuration before we start.  Fronm the left pane, select Networking.


Select the Virtual Switches tab and then click the Add Virtual Standard Switch item.


Call it something relevent (such as Storage) and select an uplink (NIC).  I’ve chosen the 2nd NIC in my system. leave everything else as standard. Click Add.


Switch to the Port Groups tab select the new vSwitch and click the Add Port Group item.


Call this Storage and assign it to the Storage virtual switch.  Click Add.  This essentially, binds the uplink to the portgroup to the switch to create a dedicated path way for storage traffic.


Finally, we need to create a VMkernel NIC. VMware uses these to pass certain types of traffic within the system.  There is already one created for management by default (called vmk0) but we need to create one for storage traffic.Select the VMkernel NIC’s tab and select the Add VMkernel NIC item.


Select the Storage Port Group and change the IPv4 Settings to Static.  You’ll need to click the little arrow to actually show the fields to enter the address. Now add in the networking information for the port.  You will need an IP address on the same subnet as the iSCSI storage as well as the subnet information and gateway.  You do not need to specify the type of traffic for the kernel port when configuring for storage.  Click Create.


Now head back to the storage information by selecting Storage from the left pane.  Select the Adapters tab and select the Configure iSCSI item to bring back up the configuration screen.


Click the Add Port Binding item in the Network Port Bindings  section and select the storage (vmk1) interface we just created.


Now select the Add Dynamic Targets from the Dynamic targets section.  Add in the IP address of the iSCSI server.and click Save Configuration.  In my case this is the IP address of the network port on my NAS which handels iSCSI traffic.  The port is default at 3260 inless you’ve configured your iSCSI server with something different.


Click Save Configuration. VMware should rescan all your adapters and, if configured correctly. you should see your iSCSI LUNS listed in the Devices tab.


Finally, select the datastores tab and click refresh.  This should refresh the screen and show that there are now datastores available to the ESXi Host.


Wrap Up

That’s it.  You now have an ESXi host ready to be used for creating VMs and your lab.  At this point I would recomend repeating the steps above for all the other physical hosts you have.  Then you are in the position where you can install Virtual Center and really start to use the softwares power.  I’ve got a sectionon how to isntall  the VCSA in Part 2 of this beginners guide.